Products
|
ARTEMiS ARTEMIS is a suite of fixed-step solvers and algorithms that optimize Simulink models of elecromechanical systems, created using the SimPowerSystems, for real-time execution. |
|
 |
EMTP-RT Real-Time Simulation Interface for EMTP-RV. |
|
JMAG-RT
|
|
|
RT-EVENTS RT-EVENTS Blockset is an add-on that works with MATLAB Simulink(tm) to improve the efficiency and accuracy of continuous-time and discrete-time systems simulations whose dynamics change due to discrete events. |
|
 |
RT-LAB Professional RT-LAB, fully integrated with MATLAB/Simulink®, is the open Real-Time Simulation software environment that has revolutionized the way Model-based Design is performed. RT-LAB’s flexibility and scalability allow it to be used in virtually any simulation or control system application, and to add computing-power to simulations, where and when it is needed. |
 |
RT-XSG RT-XSG enables engineers to generate custom, application specific models that can be implemented onto an FPGA device. Signal conditioning and conversion modules are also available that enable the custom model to be used for Real-Time Simulation, and Hardware-in-the-Loop (HIL) data processing. Note: RT-XSG software requirements can be found in the RT-XSG User Guide accessible from the documentation tab. |
 |
DriveLab The RT-LAB DriveLab is a fully integrated Hardware-in-the-Loop electrical drive experimentation platform. The system has been specially designed to be simple and robust for use in educational laboratories but is sufficiently open to allow professor or students to expand the system to their requirements. |
 |
eDRIVEsim eDRIVEsim® is an advanced real-time, hardware-in-the-loop (HIL) simulator designed for Electronic Control Unit (ECU) testing of motor drives, power electronics, and electromechanical systems. eDRIVEsim can run full motor simulation with a very small step size under 10 microseconds, enabling the simulation of high rotational speeds and switching frequencies. For ultra-low timestep and latency, eDRIVEsim uses FPGA co-processor as real-time target to achieve simulation time steps under one (1 µs) microsecond. |
 |
eMEGAsim Large Scale Multi-Processor FPGA-based Power Grid Simulator eMEGAsim is ideal for the Real-Time Simulation of large power systems models. Scalable from 6 to 64 processors and using very fast 10 Gbits/s communications links, eMEGAsim can simulate your model with a very small step size. FPGA co-processors, supported through the use of Opal-RT's RT-XSG blockset can be used to push simulation time steps down to the nanoseconds range. |
 |
PC/104 Rapid Control Prototyping A modular, compact and very robust, real-time, algorithm prototyping system based on industry-standard PC104 bus architectures and packaging for applications requiring hardened systems and extended ranges of operating temperatures |
 |
Power System Frequency Control : RT-LAB BERTA Speed Governor Test Bench RT-LAB BERTA is the best tool available today for solving speed regulator problems at the source, and at the lowest possible cost |
 |
RT-Accelerator for xPC Target RT-Accelerator for xPC Target is a high-performance xPC TARGET ™ based Control prototyping and HIL systems integrating Opal-RT's FPGA processor-based IO systems. RT-Accelerator for xPC Target can also be used to develop FPGA based models and signal processing function using RT-XSG and XILINX System Generator. |
 |
HIL Box The RT-LAB HILbox features an integrated enclosure for specialized signal conditioning units (SCU). The compartment can accommodate up to 6 SCU cartridges, each comprising a carrier board, up to 2 signal conditioning modules, 96-way input connector, edge connector into the internal routing cables, and an aluminum enclosure for maximum electromagnetic screening. |
 |
Wanda 3U 3U Rackmount enclosure with 4 rear I/O slots |
 |
Wanda 4U 4U Rackmount Chassis with rear I/O slots |
 |
OP5251 - Opto-Isolated 32 Digital Inputs & 32 Digital Output Module The OP5251 is one of a range of optional versatile Signal Conditioning Interfaces for the Opal-RT Technologies state of the art HIL (hardware in the loop) systems (The OP5000 series). It is planned to be used where electrical decoupling, ground loop elimination is required or in high voltage environment where complete isolation is a must. |
 |
OP5252 - Opto-Isolated 64 Digital Output Module The OP5252 is one of a range of optional versatile Signal Conditioning Interfaces for the Opal-RT Technologies state of the art HIL (hardware in the loop) systems (The OP5000 series). It is planned to be used where electrical decoupling, ground loop elimination is required or in high voltage environment where complete isolation is a must. |
 |
OP5253 - Opto-Isolated 64 Digital Inputs Module The OP5253 is one of a range of optional versatile Signal Conditioning Interfaces for the Opal-RT Technologies state of the art HIL (hardware in the loop) systems (The OP5000 series). It is planned to be used where electrical decoupling, ground loop elimination is required or in high voltage environment where complete isolation is a must. |
|
EMTP-RV The EMTP-RV platform for off-line simulation and analysis of transients in power systems is used by many of the world’s electrical utilities to evaluate system transients expected on transmission lines and other equipment. |
|
 |
MATRIXx Opal-RT is a National Instruments Alliance Partner. They have recently acquired MATRIXx to supply engineering development tools for dynamic modeling and control applications. |
|
SimPowerSystems SimPowerSystems extends Simulink with tools for modeling and simulating basic electrical circuits and detailed electrical power systems. These tools let you model the generation, transmission, distribution, and consumption of electrical power, as well as its conversion into mechanical power. SimPowerSystems is well suited to the development of complex, self-contained power systems, such as those in automobiles, aircraft, manufacturing plants, and power utility applications. |
