> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/electric-machines-courseware/mastering-induction-machines-using-real-time-simulation-laboratories/virtual-test-bench-overview.md).

# Virtual Test Bench Overview

## Introduction <a href="#id-2.1-diagram-and-nomenclature-of-the-virtual-test-bench-components" id="id-2.1-diagram-and-nomenclature-of-the-virtual-test-bench-components"></a>

This simulator test bench was designed to foster user interaction and to provide a wide range of experiments.

The basic teaching approach for electric machines consists in using both lectures and practical exercises to teach the fundamentals, operating modes and characteristics, modelling on steady state and transient period, and finally, industrial applications.

Laboratory exercises are an essential complement to theory.\
They allow students to experience test implementation of real devices that consider the limits imposed by the protection systems.\
Furthermore, the characterization tests of electrical machine models at reduced power are an essential goal for lab tests performed as a part of training.

The user can take advantage of this virtual simulator to understand the typical sizing methods for electrical networks and industrial applications using electric machine models with several levels of complexity.\
These models are integrated into powerful simulation tools that operate in real-time or offline.\
The main problem, often overlooked in training programs, is identifying model parameters for real devices.\
When designing or sizing a specific installation, the simulation can only be efficient if the model of the implemented system represents real behavior.

The five basic induction machine tests included in this manual were developed with these problems in mind and allow users to learn:

* Induction machine operating modes, specifically for the wound rotor machine during phase-shifting transformer mode and frequency converter mode.
* Identifying steady state model parameters for the induction machine using standard reduced power tests.
* Induction machine commissioning, start-up, and speed regulation procedures (and its coupled DC machine).
* Validation of the model parameters identified by direct comparison of the measured characteristics with theoretical characteristics calculated by models.

## Diagram and nomenclature of the virtual test bench components <a href="#id-2.1-diagram-and-nomenclature-of-the-virtual-test-bench-components" id="id-2.1-diagram-and-nomenclature-of-the-virtual-test-bench-components"></a>

The virtual test bench implemented in the real-time simulator is shown in Figs. 1 and 2.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FbDBYWG2Kmsdqxq9gi7nq%2F897aa21c-3189-49e3-a649-60895c29c92e.jpg?alt=media&amp;token=b8376670-2df3-4558-8c51-f7c4d5596eb0" alt="" width="480"><figcaption><p><strong>Figure 1</strong>: Virtual test bench implemented in the real-time simulator; rotor short-circuit configuration</p></figcaption></figure>

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FfFnVI8ueY55TcVToD2SC%2Fd3dfbc23-688b-4605-8bd7-dc9bffe8cfd2.jpg?alt=media&amp;token=d8deb4c9-9b41-42f8-aac3-74f591d6b392" alt="" width="404"><figcaption><p><strong>Figure 2</strong>: Virtual test bench implemented in the real-time simulator; adjustable rotor resistance configuration</p></figcaption></figure>

These are the main elements in the bench:

* A **DC machine** with independent excitation:
  * Two adjustable voltage sources SC1 and SC2 for armature and field when the DC motor is used to drive the induction machine (see Fig. 1).
  * An adjustable voltage source SC2 for the field of the DC machine and a fixed load resistance R<sub>ch</sub> when using the DC motor as a generator to represent a variable load to the induction motor (see Fig. 2).
* A **wound rotor, three-phase induction machine**.
* Command switches (<mark style="color:$danger;">**K1**</mark>) (<mark style="color:$danger;">**K2**</mark>) (<mark style="color:$danger;">**K3**</mark>) allowing users to connect the induction machine’s stator to several devices (see Fig. 1):
  * A three-phase, wye-connected, adjustable autotransformer SA1 linked to an infinite bus with a user defined constant frequency and voltage (the default value is f<sub>s</sub> = 60 Hz).
  * A PWM (pulse width modulation) inverter with variable voltage and frequency powered by batteries
  * An adjustable DC voltage source SC3 in series with two fixed limiting resistors used to measure low resistances in the asynchronous machine stator.
* Command switch (<mark style="color:$danger;">**K4**</mark>) opens the induction machine’s wound rotor windings or connects multiple devices (see Fig. 2):
  * A three phase short-circuit module.
  * A set of adjustable external resistances that can connect in series with rotor windings using switch (<mark style="color:$danger;">**K5**</mark>);
* A detachable mechanical coupling (<mark style="color:$danger;">**K**</mark><sub><mark style="color:$danger;">**6**<mark style="color:$danger;"></sub>) on the shaft connecting both machines.
* A protection system composed of fuses connected in series with all the windings from both machines: (F<sub>if</sub> ) (F<sub>ia</sub> ) (F<sub>ia</sub> ) (F<sub>ib</sub> ) (F<sub>ic</sub> ). Fuse ratings and their I<sup>2</sup>t were adjusted according to both machine specifications. These devices have the same behavior as normal fuses and allow students to safely interact with the setups.

The measurement devices associated with the virtual test bench are only represented by their measured quantities: DC voltages V<sub>a</sub> & V<sub>f</sub>, DC current I<sub>a</sub> & I<sub>f,</sub> rotational speed of shaft N and torque T<sub>u</sub>, RMS value of the voltage line-line U<sub>s</sub> and line current I<sub>s</sub>, total active and reactive power P & Q exchanged at the asynchronous machine’s stator.\
Oscilloscopes not shown on Fig.1 allow users to view or capture waveforms and instantaneous values.

Detailed descriptions of the adjustable elements (power supplies and contactors) accessible to the user on [the panel](https://www.opal-rt.com/docs/courseware/electric-courseware/electric-machines-courseware/mastering-induction-machines-using-real-time-simulation-laboratories/panels-overview.md) of the simulator.

## Electric machines nameplate ratings <a href="#id-2.2-electric-machines-nameplate-ratings" id="id-2.2-electric-machines-nameplate-ratings"></a>

### Induction machine nameplate ratings

| Parameters             | Values   | Descriptions              |
| ---------------------- | -------- | ------------------------- |
| **F**<sub>**sn**</sub> | 60 Hz    | Nominal frequency         |
| **U**<sub>**sn**</sub> | 460 V    | Nominal line-line voltage |
| **Is**<sub>**n**</sub> | 17 A     | Nominal current           |
| **P**<sub>**un**</sub> | 16 HP    | Nominal power             |
| **N**<sub>**n**</sub>  | 1746 rpm | Nominal speed             |
| **FP**<sub>**n**</sub> | 0.9      | Nominal power factor      |

### DC Machine Nameplate Ratings

| Parameters             | Values   | Descriptions             |
| ---------------------- | -------- | ------------------------ |
| **P**<sub>**un**</sub> | 16HP     | Nominal power            |
| **V**<sub>**an**</sub> | 460 V    | Nominal rotor voltage    |
| **V**<sub>**fn**</sub> | 460 V    | Nominal inductor voltage |
| **I**<sub>**fn**</sub> | 1.11 A   | Nominal inductor current |
| **N**<sub>**n**</sub>  | 1746 rpm | Nominal speed            |


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/electric-machines-courseware/mastering-induction-machines-using-real-time-simulation-laboratories/virtual-test-bench-overview.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
