> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-parallel-rlc-resonant-circuit-in-steady-state.md).

# Single-Phase Parallel RLC Resonant Circuit in Steady-State

## Objective <a href="#objective.3" id="objective.3"></a>

To better understand the resonance phenomenon in a single-phase RLC parallel circuit under an alternating monophasic voltage, we will perform this final exercise, which will help us grasp the theoretical foundations and gain a solid understanding of the topic.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FyH28y3iflLKeWTDpFRno%2F85d0e444-67e1-4415-95b2-305a5a954167.png?alt=media&amp;token=506d9a85-527a-4cee-8812-3e3c57e4c9ad" alt="" width="480"><figcaption><p><strong>Figure 4:</strong> RLC resonance parallel circuit</p></figcaption></figure>

## Preparatory activities <a href="#preparatory-activities.4" id="preparatory-activities.4"></a>

To achieve a resonant circuit, we need to perform some preliminary calculations. Let’s consider the given circuit with the following parameters:

* $$U\_0 = 230,\text{V} \\$$
* $$f = 50,\text{Hz} \\$$
* $$f(x) = x \* e^{2 pi i \xi x}$$
* $$f(x) = x \* e^{2 pi i \xi x}$$

1. Calculate the value of inductance (L) in such a way that the apparent power consumed by the circuit is minimized.
2. In the case of question 1, where the apparent power is minimized, calculate the power consumed by the resistance (R), the inductance (L), and the capacitance (C). Also, calculate and visualize the current drawn from the voltage source

   .

### Setup initialization <a href="#setup-initialization.4" id="setup-initialization.4"></a>

When the virtual laboratory is launched, the initial settings in the “Network and Transformer” tab under “Fundamental” and “Harmonic” should be adjusted as follows:

1. Set the frequency to 50 Hz.
2. Choose the network as a single-phase network with the phase A voltage of 230 V and no phase shift.
3. Set the transformer to short-circuit mode as it is not used.
4. The circuit breaker is not used; the “Without protection” button is activated.
5. Under the “Harmonic” tab, no harmonics are added. The “A” button is deactivated.
6. Under the “Passive load” tab, select the configuration “A1 + B1//C1.”

## Questions 1 and 2  <a href="#questions-1-and-2" id="questions-1-and-2"></a>

In these questions, you are asked to first calculate the value of inductance L in such a way that the apparent power consumed by the circuit is minimized. Then, you need to calculate the power consumed by each component.

### **1- The setup**

The requested setup can be done under the “Passive load” tab as follows:

a) Set the impedance Z\_1\_Series to non-equilibrium mode and choose component A and C as short circuits, and component B as an open circuit. This impedance is not used in this exercise, but to avoid influencing the circuit, these settings need to be adjusted.

b) Set the impedance Z\_1\_Parallels to non-equilibrium mode and choose component A as an RLC impedance with the values R=10Ohm, L=2.53mH, and C=4mF.

c) The other two impedances are balanced circuits with component A as a short circuit.

### **2- Take measurements**

Once the setup is complete, you need to take measurements:

1. In the “Network and Transformer” tab, activate the “Power On” button.
2. Open the “Measurements and Calculations” tab and select “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. For both measurements, phase A is observed.
3. Observe the signals using the measurements and under the “Oscilloscope” tab, and verify the phase difference.

## Laboratory report <a href="#laboratory-report.3" id="laboratory-report.3"></a>

1. Perform the preparatory activities.
2. Present and comment on the oscillogram for each question.
3. Compare the theoretical values with the measured values.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-parallel-rlc-resonant-circuit-in-steady-state.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
