> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-rl-and-rc-circuit-in-steady-state.md).

# Single-Phase RL and RC Circuit in Steady-State

## Objective <a href="#objective" id="objective"></a>

This exercise aims to highlight the relationships between voltage and current in the case of a passive load consisting of inductive and capacitive elements under single-phase alternating voltage in steady-state conditions.

## Single-phase RL circuit in steady-state <a href="#part-1-single-phase-rl-circuit-in-steady-state" id="part-1-single-phase-rl-circuit-in-steady-state"></a>

In the first part, the circuit to observe consists of a series combination of a resistor and an inductance.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FHlYb2upEFvldL07SsPv0%2F5e9aae20-fe50-4a0d-8413-2cc27abe2686.png?alt=media&amp;token=ff853c61-90a9-4e0d-9b71-b6133395a03e" alt="" width="480"><figcaption><p><strong>Figure 1:</strong> RL circuit</p></figcaption></figure>

### **Preparatory activities**

To create the requested circuit and better understand the fundamentals, theoretical exercises are requested. The values of the circuit elements are as follows:&#x20;

Voltage source: $$u\_0(t) = \sqrt{2} \* 230 \* \sin(\omega t),\text{V}$$

Source frequency: $$f = 50,\text{Hz}$$

* $$R = 20,\Omega$$
* $$L = 100,\text{mH}$$

Calculate the instantaneous value of the current $$i(t)$$ and display the obtained function on the virtual laboratory’s oscilloscope.&#x20;

Same as question 1 but with a source frequency of $$f = 100,\text{Hz}$$.&#x20;

1. Visualize the current obtained on the virtual laboratory’s oscilloscope.

Calculate the value of the resistance so that the phase difference φ between the voltage $$u\_0(t)$$ and the current $$i(t)$$ is 45° for a source frequency of $$f = 50,\text{Hz}$$. Also, visualize the current obtained on the virtual laboratory’s oscilloscope.

### **Setup initialization**

When the virtual laboratory is launched, the initial parameters in the “Network and Transformer” tab under “Fundamental” and “Harmonic” are set as follows:

a) Set the frequency to 50 Hz.

b) Choose the network as a single-phase network with a phase A voltage of 230 V (since it’s a single-phase network, the phases are set as unbalanced) and no phase shift.

c) Set the transformer in short-circuit mode because it’s not being used.

d) The circuit breaker is not being used; the “Without protection” button is activated.

e) Under the “Harmonic” tab, no harmonics are added. The “A” button is deactivated.

f) Under the “Passive load” tab, choose the configuration “A1 + B1//C1.”

### **Question 1**

In the first question, you are asked to calculate the instantaneous value of the current $$i(t)$$ and visualize the obtained function on the virtual laboratory’s oscilloscope.

#### **1- The setup**

The requested setup can be performed under the “Passive load” tab as follows:

a) Set impedance Z\_1\_Series to non-balanced mode (as it’s a single-phase circuit) and choose component A as an RL impedance with values R=20 Ohms and L=100 mH. Components B and C are short-circuited.

b) The other three impedances are balanced circuits with component A short-circuited; they are not used.

#### **2- Take measurements**

Once the setup is completed, the remaining steps are as follows:

a) In the “Network and Transformer” tab, activate the “Power On” button.

b) Open the “Measurements and Calculations” tab and select “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. For both measurements, observe phase A.

c) Observe the signals using the measurements in the “Oscilloscope” tab.

### **Question 2**

For question 2, it’s the same process, but with a source frequency of $$f = 100,\text{Hz}$$

. Visualize the current obtained on the virtual laboratory’s oscilloscope.

In this exercise, the setup from the previous exercise remains the same, but the frequency of phase A is changed to 100Hz. Take the same measurements as in question 1 and compare them.

### **Question 3**

For question 3, you are asked to calculate the value of the resistance so that the phase difference φ between the voltage $$u\_0(t)$$ and the current $$i(t)$$ is 45° for a source frequency of $$f = 50,\text{Hz}$$ .&#x20;

Then, visualize the current obtained on the virtual laboratory’s oscilloscope.

#### **1- The setup**

The requested setup can be performed under the “Passive load” tab as follows:

a) Set impedance Z\_1\_Series to non-balanced mode and choose component A as an RL impedance with the value L=100mH and the value of R as calculated. Components B and C are short-circuited.

b) The other three impedances are balanced circuits with component A short-circuited.

#### **2- Take measurements**

Once the setup is complete, it remains to take the measurements:

a) In the “Network and Transformer” tab, activate the “Power On” button.

b) Open the “Measurements and Calculations” tab and choose “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. For both measurements, phase A is observed.

c) Observe the signals using the measurements in the “Oscilloscope” tab, and verify the requested phase difference in the exercise.

## Single-Phase RC circuit in steady-state <a href="#part-2-single-phase-rc-circuit-in-steady-state" id="part-2-single-phase-rc-circuit-in-steady-state"></a>

In the second part, the circuit to observe consists of a circuit composed of a resistance R2 in parallel with a capacitor C. This element is in series with a resistance R1.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2F7Lkb99R5fPT37AmL2jmH%2F61df0b14-beda-4799-b4c8-d1b039483733.png?alt=media&amp;token=410e81d6-6209-4807-b618-7d7d8a333dc7" alt="" width="480"><figcaption><p><strong>Figure 2:</strong> RC circuit</p></figcaption></figure>

### **Preparatory activities**

To create the required circuit and better understand the fundamentals, theoretical exercises are requested. The values of the circuit elements are as follows:

* Voltage source: $$u\_0(t) = \sqrt{2} \* 230 \* \sin(\omega t),\text{V}$$
* Source frequency: $$f = 50,\text{Hz}$$
* $$R\_1 = 5,\Omega$$
* $$R\_2 = 10,\Omega$$
* $$C = 318.3,\mu\text{F}$$

Calculate the current $$i\_C(t)$$ at time $$t\_1 = 8,\text{ms}$$ and the current I. Visualize the current  on the oscilloscope of the virtual laboratory. The circuit is in a steady-state.

### **Setup initialization**

When the virtual laboratory is launched, the initial settings in the “Network and Transformer” tab under “Fundamental” and “Harmonic” should be adjusted as follows:

1. Set the frequency to 50 Hz.
2. Choose the network as a single-phase network with phase A voltage of 230 V and no phase shift.
3. Set the transformer to short-circuit mode as it is not used.
4. The circuit breaker is not used; the “Without protection” button is enabled.
5. Under the “Harmonic” tab, no harmonics are added. The “A” button is disabled.
6. In the “Passive load” tab, choose the configuration “A1 + B1//C1”.

### **Question 1**

In this exercise, you are asked to calculate the current at the time= 8 ms and the current I. Then, you need to visualize the current $$i(t)$$ on the oscilloscope of the virtual laboratory.

#### **1- The setup**

The requested setup can be created in the “Passive load” tab as follows:

1. Set the impedance Z\_1\_Series to non-equilibrium mode and choose component A as a pure ohmic resistance with R = 5 Ohms. Components B and C are short-circuited.
2. Set the impedance Z\_1\_Parallels to non-equilibrium mode and choose component A as an RC impedance with the values R = 10 Ohms and C = 318.6 μF.
3. The other two impedances are balanced circuits with component A short-circuited

#### **2- Take measurements**

Once the setup is complete, you need to take the following measurements:

1. In the “Network and Transformer” tab, activate the “Power On” button.
2. Open the “Measurements and Calculations” tab and select “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. For both measurements, observe phase A.
3. Observe the signals using the measurements and in the “Oscilloscope” tab.

## **Laboratory report**

The tasks to be performed for each part are as follows:

1. Perform the preparatory activities.
2. Present and comment on the oscillogram for each question.
3. Compare the theoretical values with the measured values.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-rl-and-rc-circuit-in-steady-state.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
