> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-series-rlc-resonant-circuit-in-steady-state.md).

# Single-Phase Series RLC Resonant Circuit in Steady-State

## Objective <a href="#objective.2" id="objective.2"></a>

In this exercise, it’s a single-phase RLC circuit with the aim of achieving resonance behavior.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FXzWx9kh1RtGu1XJ7HNV7%2F742f3fd3-8119-4ad6-b1df-6a429a49993d.png?alt=media&amp;token=4b8476bc-7da7-474d-bb18-bab0c5d475e6" alt="" width="480"><figcaption><p><strong>Figure 3:</strong> RLC resonance series circuit</p></figcaption></figure>

## Preparatory activities <a href="#preparatory-activities.3" id="preparatory-activities.3"></a>

To create a resonant circuit, some preliminary calculations need to be performed. Consider the circuit above with the following data:

* $$U = 230,\text{V}$$
* $$f = \[50; 200],\text{Hz}$$
* $$R = 1,\Omega$$
* $$C = 4,\text{mF}$$

1. Calculate the value of inductance L and determine the source frequency for the voltage across the capacitor $$U\_C$$ to be maximum.
2. What should be the source voltage $$U\_0$$ for the voltage across the capacitor to be $$U\_C$$ = 200 V?
3. In this case, what is the current **I**, and what is the maximum energy stored in the inductance and the capacitance, denoted as $$W\_L$$ and $$W\_C$$ ? Also, visualize the current function $$i(t)$$ .
4. Considering the maximum available inductance is 2 mH, what is the frequency value for the voltage across the capacitor $$U\_C$$ to remain maximum?&#x20;
5. In this case, what are the values of current **I** and voltage $$U\_0$$ ?

### Setup initialization <a href="#setup-initialization.3" id="setup-initialization.3"></a>

When the virtual laboratory is launched, the initial settings in the “Network and Transformer” tab under “Fundamental” and “Harmonic” are set as follows:

1. Set the frequency to 50 Hz.
2. Choose the network as a single-phase network with the phase A voltage of 230 V and no phase shift.
3. Set the transformer to short-circuit mode as it is not used.
4. The circuit breaker is not used; the “Without protection” button is activated.
5. Under the “Harmonic” tab, no harmonics are added. The “A” button is deactivated.
6. Under the “Passive load” tab, choose the ’A1 + B1//C1’ setup.

## Questions 1, 2, and 3 <a href="#questions-1-2-and-3" id="questions-1-2-and-3"></a>

In this section, you are first asked to calculate the value of the inductance L and determine the frequency of the source for the voltage across the capacitor $$U\_C$$ to be maximum.&#x20;

The value of the inductance is defined to achieve a resonant behavior. With these calculated values, you need to find the source voltage $$U\_0$$ for the voltage across the capacitor to be $$U\_C$$ =200 V. In the final question, the energies stored in the inductance and in the capacitor are discussed.

### **1- The setup**

The requested setup can be performed under the “Passive load” tab:

1. Set the impedance Z\_1\_Series to non-balanced mode and choose component A as an impedance RLC with the values R=1Ohm, C=4mF, and L as calculated before. The components B and C are short circuits.
2. The three other impedances are balanced circuits with component A short-circuited.

### **2- Take measurements**

Once the setup is complete, it remains to take measurements:

1. In the “Network and Transformer” tab, activate the “Power On” button.
2. Open the “Measurements and Calculations” tab and select “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. For both measurements, phase A is observed.
3. Observe the signals using the measurements and in the “Oscilloscope” tab. Compare the phase shift with the calculated value.

## Question 4 <a href="#question-4" id="question-4"></a>

In the last part, you are asked to repeat the first question but with a constraint on the inductance, which should be a maximum of 2mH. You need to determine the frequency for which the voltage across the capacitor $$U\_C$$ remains maximum, as well as the voltage to be applied.

### **1- The setup**

The requested setup can be done under the “Passive load” tab as follows:

1. In the “Network and Transformer” tab, set the frequency and phase A voltage to the previously calculated values.
2. Set the impedance Z\_1\_Series to the unbalanced mode and choose component A as an RLC impedance with the values R=1Ohm, L=2mH, and C=4mF. Components B and C are short circuits.
3. The other three impedances should be balanced circuits with component A as a short circuit.

### **2- Take measurements**

Once the setup is complete, you need to take the measurements:

1. In the “Network and Transformer” tab, activate the “Power On” button.
2. Open the “Measurements and Calculations” tab and select “Rés U” for measurement 1 and “Rés Z\_1 I” for measurement 2. Make sure to observe phase A for both measurements.
3. Observe the signals using the measurements and in the “Oscilloscope” tab. Verify the phase shift.

## **Laboratory report**

1. Perform the preparatory activities.
2. Present and comment on the oscillogram for each question.
3. Compare the theoretical values with the measured values.
4. What is the advantage of having a variable-frequency voltage source?


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/single-phase-systems/single-phase-series-rlc-resonant-circuit-in-steady-state.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
