> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/three-phase-systems/3-phase-passive-circuit-in-steady-state-arranges-in-star-configuration.md).

# 3-Phase Passive Circuit in Steady-State Arranges in Star Configuration

## Objective <a href="#objective" id="objective"></a>

We have a balanced three-phase load connected in a star (Y) configuration, consisting of an inductance L = 12 mH and a resistance R = 10 Ω. This load, which could be a motor, is supplied by a direct symmetrical three-phase network with a line voltage U = 400 V and a frequency f = 50 Hz. The reference for the voltage will be placed on the phase voltage $${U\_1}$$ .&#x20;

The equivalent circuit is shown below:

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FjgGDTqJKqEH2QO0N2Ljt%2F6b7212bd-e257-415c-b93f-af7d8f143fec.png?alt=media&amp;token=d56bfea1-0e85-4a15-a4d0-631210d68d5d" alt=""><figcaption><p><em><strong>Figure 1:</strong> Symmetrical Three-Phase RL Load Connected in Star Configuration</em></p></figcaption></figure>

## Preparatory activities <a href="#preparatory-activities" id="preparatory-activities"></a>

In order to set up the requested circuit and gain a better understanding of the basics, theoretical exercises are required. The values of the circuit elements are as follows:

* $$U\_{\text{line}} = 400,\text{V} \\$$
* $$f = 50,\text{Hz} \\$$
* $$R = 10,\Omega \\$$
* $$L = 12,\text{mH}$$

1. Calculate the current flowing in each of the three phases, provide the phasor representation as well as the instantaneous value of the three currents. Visualize the currents using the oscilloscope in the virtual laboratory and compare them with the calculated currents.
2. Calculate the current flowing in the three lines, provide the phasor representation and instantaneous value. Visualize the line currents on the oscilloscope. Compare them with the results from question 1.
3. Calculate the power factor of the circuit and validate it by visualizing the functions and/or measurements on the oscilloscope in the virtual laboratory.

### Setup initialization <a href="#setup-initialization" id="setup-initialization"></a>

When the virtual laboratory is launched, the initial settings in the "Network and Transformer" tab under "Fundamental" and "Harmonic" are configured as follows:

1. Set the frequency to 50 Hz.
2. Choose the network as a three-phase network with a phase voltage of 230 V and no phase shift.
3. Activate the "Phase Inversion" button to obtain results equivalent to calculations (according to the convention).
4. Set the transformer to short-circuit mode as it is not used.
5. The circuit breaker is not used; the "Without protection" button is activated.
6. Under the "Harmonic" tab, no harmonics are added. The "A" button is disabled.
7. Under the "Passive load" tab, choose the configuration "Star".

## Question 1 <a href="#question-1" id="question-1"></a>

In the first exercise, you are asked to calculate the current flowing in each of the three phases.

#### 1- The setup <a href="#id-1-the-setup" id="id-1-the-setup"></a>

The requested setup can be created in the "Passive load" tab as follows:

* Set the impedance Z\_1\_Series to balanced mode and choose component A as an RL impedance with values R = 10 Ω and L = 12 mH.
* The other three impedances are balanced circuits with component A short-circuited.

#### 2- Take measurements <a href="#id-2-take-measurements" id="id-2-take-measurements"></a>

Once the setup is complete, you need to take measurements:

* In the "Network and Transformer" tab, activate the "Power On" button.
* Open the "Measurements and Calculations” tab and measure "Rés Z\_1 U" and "Rés Z\_1 I" for each phase. Observe the magnitudes and phase angles of voltages and currents, as well as the phase shift. Compare with the theoretical values.
* Observe the signals using measurements and the "Oscilloscope" tab.
* Observe the behavior in case "Phase Inversion" is not activated.

## Question 2 <a href="#question-2" id="question-2"></a>

In this question, you are asked to calculate the current flowing in the three lines.

### 1- The setup <a href="#id-1-the-setup.1" id="id-1-the-setup.1"></a>

The requested setup can be created in the "Passive load" tab as follows:

* Set the impedance Z\_1\_Series to balanced mode and choose component A as an RL impedance with values R = 10 Ω and L = 12 mH.
* The other three impedances are balanced circuits with component A short-circuited.

### 2- Take measurements <a href="#id-2-take-measurements.1" id="id-2-take-measurements.1"></a>

Once the setup is complete, you need to take measurements:

* In the "Network and Transformer" tab, activate the "Power On" button.
* Open the "Measurements and Calculations" tab and measure "Rés Z\_1 U" and "Rés Z\_1 I" for each phase. Observe the magnitudes and phase angles of voltages and currents, as well as the phase shift. Compare with the theoretical values.
* Observe the signals using measurements and the "Oscilloscope" tab.

## Question 3 <a href="#question-3" id="question-3"></a>

In this question, you are asked to calculate the power factor of the circuit.

### Take measurements <a href="#take-measurements" id="take-measurements"></a>

The setup remains the same, and you need to take measurements:

* In the "Network and Transformer" tab, activate the "Power On" button.
* Open the "Measurements and Calculations" tab and observe the active and apparent power, and deduce the power factor.
* Compare the phase angle obtained from the power factor with the calculated angle.

## Laboratory report <a href="#laboratory-report" id="laboratory-report"></a>

1. Perform the preparatory activities.
2. Present and comment on the oscillogram for each question.
3. Compare the theoretical values with the measured values.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/fundamentals-of-electrical-engineering/three-phase-systems/3-phase-passive-circuit-in-steady-state-arranges-in-star-configuration.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
