> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/courseware/electric-courseware/power-electronics/ac-to-dc-rectifiers/single-phase-diode-bridge-rectifier/operating-principle.md).

# Operating Principle

## Operating principle without smoothing capacitor value <a href="#operating-principle-without-smoothing-capacitor-value" id="operating-principle-without-smoothing-capacitor-value"></a>

The four diodes labeled D1 to D4 are arranged in “series pairs” with only two diodes conducting current during each half cycle.&#x20;

* During the positive half cycle of the supply, diodes D1 and D4 conduct in series while diodes D2 and D3 are reverse biased and the current flows through the load as shown in figure 5.
* During the negative half cycle of the supply, diodes D2 and D3 conduct in series, but diodes D1 and D4 are “OFF” as they are now reverse biased.\
  The current flowing through the load is in the same direction as the positive cycle (see figure 6).

This is a double-way topology. In each half-cycle, the current flows in both directions in the secondary winding, but always in the same direction in the load.

The bridge is fed by a sinusoidal AC voltage so that:

$$
V\_e = V\_m \sin(\omega t) = V\_e \sqrt{2},\sin(\omega t) \quad \quad (1) \\\[8pt]
$$

*With:*

$$V\_e$$:  the RMS value of the input voltage

$$V\_m$$: the peak value of the input voltage

It’s assumed that the four diodes are perfect and identical.

For the positive cycle: $$V\_e(t) > 0 ; ; ; 0 \le t \le \frac{T}{2}$$

* D1 and D4 conduct
* D2 and D3 switch “OFF”.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FcIpAIKpyCFMNM4D9zKUA%2F17c20f3d-b0ee-4d1b-80d5-301caebcfd7d.png?alt=media&amp;token=3aaec8f3-f6f2-4827-ab57-1653fd8ad85e" alt=""><figcaption><p><strong>Figure 5</strong>: Positive Cycle of the Single-Phase Diode Bridge Rectifier</p></figcaption></figure>

Thus, we obtain:

$$
V\_s(t) = V\_e(t) \quad \quad (2) \\\[8pt]
$$

For the negative cycle: $$V\_e(t) < 0 ; ; ; \frac{T}{2} \le t \le T$$

* D2 and D3 conduct
* D1 and D4 switch “OFF”.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2F2A7elkBREAI0gI7flkId%2F28b42ff3-b0c0-4b2b-8278-82100fc5fab0.png?alt=media&amp;token=af35da05-614d-493d-98ff-6fd4e22a4475" alt=""><figcaption><p><strong>Figure 6:</strong> Negative Cycle of the Single-Phase Diode Bridge Rectifier</p></figcaption></figure>

Thus, we obtain:

<p align="center"> <span class="math">V_s(t) = -V_e(t) \quad \quad (3) \\[8pt]</span></p>

The output voltage is periodic of period $$\frac{T}{2}$$. \
The average output voltage is calculated as follows:

$$
\langle V\_s(t) \rangle
\= \frac{1}{T/2}\int\_{0}^{T/2} V\_e(t),dt
\= \frac{1}{T/2}\int\_{0}^{T/2} V\_e\sqrt{2},\sin(\omega t),dt
\\\[8pt]
$$

Therefore, it leads to an average output voltage of:

$$
\langle V\_s \rangle
\= \frac{2}{\pi},\sqrt{2},V\_e
\= \frac{2}{\pi},V\_m \quad \quad (4)
\\\[8pt]
$$

With:

$$
V\_m = \sqrt{2},V\_e \\\[8pt]
$$

The average output current is obtained using Ohm’s law:

$$
\langle i\_s \rangle = \frac{\langle V\_s \rangle}{R} = \frac{2,V\_m}{\pi,R} \quad \quad (5) \\\[8pt]
$$

The root-mean-square (RMS) value of the output voltage is:

$$
V\_s = \frac{V\_m}{\sqrt{2}} \quad \quad (6) \\\[8pt]
$$

The root-mean-square (RMS) value of the output current is:

$$
I\_s = \frac{V\_s}{R} = \frac{V\_m}{\sqrt{2},R} \quad \quad (7) \\\[8pt]
$$

To analyze the performance of a rectifier circuit, the form factor and the ripple factor are often used.

The form factor is the ratio of the RMS output voltage and the average output voltage:

$$
F = \frac{V\_s}{\langle V\_s \rangle} \quad \quad (8) \\\[8pt]
$$

The more F tends to 1, the more the rectified output voltage can be regarded as continuous.

The ripple factor can be calculated as follows:

$$
\tau = \frac{V\_{s,\max} - V\_{s,\min}}{\langle V\_s \rangle} \quad \quad (9) \\\[8pt]
$$

Where:\
$$-V\_s$$ is the maximum peak value of the output voltage\
$$-V\_s$$ is the minimum peak value of the output voltage

The more $$\tau$$ tends to 0, the more the rectified output voltage can be considered as continuous.

## Operating Principle with Smoothing Capacitor Value <a href="#operating-principle-with-smoothing-capacitor-value" id="operating-principle-with-smoothing-capacitor-value"></a>

Rectifiers are normally used in circuits that require a steady voltage to be supplied. The raw rectified DC requires a smoothing capacitor circuit to enable the rectified DC to be smoothed so that it can be used to power electronic circuits without large levels of voltage variation.\
To smooth the output of the rectifier, a reservoir capacitor is used - placed across the output of the rectifier and in parallel with the load.\
This capacitor charges up when the voltage from the rectifier rises above that of the capacitor and then as the rectifier voltage falls, the capacitor provides the required current from its stored charge.

<figure><img src="https://4054096626-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FYbyVjpgEQX9nfCkpYoFP%2Fuploads%2FsVgssEAzegBiQQZVS8n9%2Fc1901cad-3f53-47a7-addd-b59501b9f126.png?alt=media&amp;token=3daa1f8c-1765-4951-8a17-32ff7016d4ed" alt=""><figcaption><p><strong>Figure 7:</strong> Single-Phase Diode Bridge Rectifier with Smoothing Capacitor</p></figcaption></figure>

The choice of capacitor value needs to fulfil a number of requirements.\
In the first case, the value must be chosen so that its time constant is very much longer than the time interval between the successive peaks of the rectified waveform:

$$
R \cdot C \gg \frac{1}{f} \\\[8pt]
$$

Where :

$$R$$: the overall resistance of the load for the supply

$$C$$: the value of capacitor

$$f$$:  the ripple frequency - this will be twice the line frequency when a full wave rectifier is used

The ripple voltage is not only determined by the value of the smoothing capacitor, but the frequency and the load current.\
It is calculated as:

$$
\Delta V\_s = \frac{V\_s}{f \cdot R \cdot C} = \frac{I\_s}{f \cdot C} \quad \quad (10)\\\[8pt]
$$

Where:&#x20;

$$I\_s$$: the DC load current

$$f$$: the frequency of the ripple or twice the input frequency in Hertz

$$C$$: the capacitance&#x20;

It can be noted from equation (10) that the ripple voltage is inversely proportional to the resistance.\
So, we can conclude that for C constant, the peak-to-peak voltage decreases as the resistance increases and therefore the curve is smoothed.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/courseware/electric-courseware/power-electronics/ac-to-dc-rectifiers/single-phase-diode-bridge-rectifier/operating-principle.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
