> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/hyperlab/example-models/power-electronics/full-wave-rectifier.md).

# Full-wave Rectifier

## Description

A Full-Wave Rectifier is a power electronic circuit designed to convert an alternating current (AC) voltage into a unidirectional, pulsating direct current (DC) voltage. Unlike a half-wave rectifier, which uses only one half of the AC waveform, a full-wave rectifier utilizes both the positive and negative half-cycles of the input signal.

This example uses a **four-diode bridge rectifier**, also known as a Graetz bridge, to convert the sinusoidal input voltage into a positive output voltage.

A smoothing capacitor connected across the load can reduce output voltage fluctuations, producing a more stable DC voltage.

## Requirements

This example does not require any additional resources.

## Detailed explanation

This example allows users to investigate the behavior of a Full-Wave Rectifier and understand how a smoothing capacitor influences the quality of the DC output voltage.

The input voltage is a sinusoidal AC waveform with a peak amplitude of approximately **100 V**, as illustrated in the graph.

The interactive interface provides a circuit schematic, voltage measurements, and real-time graphs displaying:

* **Input voltage (v\_src):** The sinusoidal AC voltage applied to the diode bridge.
* **Output voltage (v\_R):** The rectified voltage measured across the load resistor.

Users can modify the smoothing capacitor value to investigate its influence on output voltage ripple.

<figure><img src="https://2712201518-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2Fbs0l9jugXixa0ghErrqs%2Fuploads%2FSqeTXGNOKHrgbazRdWXG%2Ffull-wave-rectifier.png?alt=media&amp;token=b5be2e2c-00cd-4469-9a75-34e6c2d4b6e4" alt=""><figcaption></figcaption></figure>

## Simulation and results

#### **Experiment 1 – Full-Wave Rectification**

Start with a very small smoothing capacitance, such as **1 µF (1 × 10⁻⁶ F)**.

Observe the input and output voltage waveforms.

Notice how the negative half-cycles of the input sinusoidal voltage are converted into positive half-cycles at the output.

Compare the frequency of the input waveform with the frequency of the rectified output waveform.

Verify that the output ripple frequency is twice the input AC frequency.

#### **Experiment 2 – Influence of the Smoothing Capacitor**

Increase the smoothing capacitance progressively and observe the resulting output voltage.

Suggested capacitance values:

| Capacitance | Expected Behavior                                                         |
| ----------- | ------------------------------------------------------------------------- |
| 1 µF        | Significant voltage ripple; output closely follows the rectified waveform |
| 10 mF       | Reduced voltage ripple; improved smoothing                                |
| 100 mF      | Very low voltage ripple; output approaches a constant DC voltage          |

Observe how increasing the capacitance allows the capacitor to maintain the output voltage between successive rectified peaks.

#### **Experiment 3 – Analysis of Output Voltage Ripple**

Compare the output voltage waveforms obtained with different capacitance values.

Measure the maximum and minimum output voltages and calculate the peak-to-peak ripple:

```
V_ripple = V_max - V_min
```

Analyze how the ripple amplitude decreases as the smoothing capacitance increases.

Observe that the output voltage becomes progressively more stable, approaching the peak value of the rectified input waveform.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/hyperlab/example-models/power-electronics/full-wave-rectifier.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
