> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/hypersim/model-and-simulation/phasor-domain-with-ephasorsim/integrate-a-power-system-model-to-ephasorsim/native-library-components/load-components/dynamic-load-model.md).

# Dynamic Load Model

The **Dynamic Load** component models an exponential load with three nonlinear voltage and one linear frequency dependence terms. It is based on the load model described in the *IEEE Guide for Load Modeling and Simulations for Power Systems*<sup>*1*</sup> and extends the traditional positive-sequence load representation by incorporating dynamic voltage and frequency effects.

This model is particularly useful for studies where load behavior significantly impacts system performance, including:

* Transient stability studies
* Voltage recovery analysis
* Frequency response analysis
* Disturbance and contingency simulations

The component calculates active and reactive power as functions of bus voltage and frequency, while allowing configurable dynamic response through user-defined time constants.

$$
P = P\_0 \left\[ k\_{p1}(dv\_p)^{e\_{p1}} + k\_{p2}(dv\_p)^{e\_{p2}} + k\_{p3}(dv\_p)^{e\_{p3}} \right] df\_p , k\_s
$$

$$
Q = Q\_0 \left\[ k\_{q1}(dv\_q)^{e\_{q1}} + k\_{q2}(dv\_q)^{e\_{q2}} + k\_{q3}(dv\_q)^{e\_{q3}} \right] df\_q , k\_s
$$

The output **active power** (*P*) and **reactive power** (*Q*) values, and therefore the resulting currents, are calculated using the previous equations, where:

* *P*<sub>*0*</sub> and *Q*<sub>*0*</sub> are the rated active and reactive power values specified by the user.
* *k*<sub>*p1*</sub>, *k*<sub>*p2*</sub>, *k*<sub>*p3*</sub> and *k*<sub>*q1*</sub><sub>,</sub> *k*<sub>*q2*</sub><sub>,</sub> *k*<sub>*q3*</sub> are the voltage-dependence coefficients for active and reactive power.
  * These coefficients determine the relative weight of each term in the ZIP model.
  * The coefficients are automatically normalized. For example, coefficients of `2`, `5` and `3` correspond to weights of **20%**, **50%**, and **30%**.
  * If all coefficients are zero, each term is assigned an equal weight of **1/3** to avoid division by zero.
* *e*<sub>*p1*</sub>, *e*<sub>*p2*</sub>, *e*<sub>*p3*</sub> and *e*<sub>*q1*</sub><sub>,</sub> *e*<sub>*q2*</sub><sub>,</sub> *e*<sub>*q3*</sub> are the voltage-dependence exponents for active and reactive power.
  * These exponents define how strongly the load responds to voltage variations.
  * There are no restrictions on their values. Typical values range from **−3 to +3**, although larger magnitudes (up to approximately **±25**) may be used for specific load models<sup>2</sup>.
* In practical power systems, load behavior is often modified when the voltage deviates significantly from its nominal value to maintain numerical stability. To reproduce this behavior, the ZIP Load model includes an additional voltage-dependent coefficient (*k*<sub>*s*</sub>) that limits the effect of the voltage exponents outside a predefined voltage range.
  * The coefficient is defined by the piecewise function shown below, where *v*<sub>*min*</sub> = 1 - *range* is the lower voltage threshold and *v*<sub>*max*</sub> = 1 + *range* is the upper voltage threshold. A typical value for the *range* parameter is **0.2**, defining a voltage interval of **\[0.8 pu, 1.2 pu]**. Within this interval, the load follows the specified voltage-dependence model. Outside the interval, the limiting coefficient alters the load response to improve numerical stability and avoid unrealistic behavior at extreme voltages.

$$
k\_s = \begin{cases} \dfrac{2|v|^2}{v\_{\min}^2}, & |v| < \dfrac{v\_{\min}}{2} \\\[10pt] 1 - 2\left(\dfrac{|v|-v\_{\min}}{v\_{\min}}\right)^2, & \dfrac{v\_{\min}}{2} \le |v| \le v\_{\min} \\\[10pt] 1, & v\_{\min} < |v| < v\_{\max} \\\[10pt] 1 + \left(|v|-v\_{\max}\right)^2, & |v| \ge v\_{\max} \end{cases}
$$

* *dv*<sub>*p*</sub>​ and *dv*<sub>*q*</sub>​ are the delayed voltage deviations used to compute the active and reactive power responses. They are obtained by applying the first-order transfer functions shown below to the voltage deviation signal.
  * *v*<sub>*0*</sub>​ (pu) is the reference voltage corresponding to the nominal operating point, at which *P* = *P*<sub>*0*</sub><sub>​</sub> and *Q* = *Q*<sub>*0*</sub>.
  * The voltage deviation is calculated from the terminal voltage relative to the reference voltage *v*<sub>*0*</sub>.
  * *k*<sub>*P*</sub> = *k*<sub>*p1*</sub>*e*<sub>*p1*</sub> + *k*<sub>*p2*</sub>*e*<sub>*p2*</sub> + *k*<sub>*p3*</sub>*e*<sub>*p3*</sub>
  * *k*<sub>*Q*</sub> = *k*<sub>*q1*</sub>*e*<sub>*q1*</sub> + *k*<sub>*q2*</sub>*e*<sub>*q2*</sub> + *k*<sub>*q3*</sub>*e*<sub>*q3*</sub>
  * *tpv* and *tqv* are the voltage-dependence time constants for the active and reactive power responses.
  * *t*<sub>*1*</sub>*​* is the dynamic load time constant.

<figure><img src="https://3623212549-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FLxgTpoh7kyPmQ5vuyqD7%2Fuploads%2Fgit-blob-b96e71a0f6d392d5ff435c14f855b1b0c9911195%2Feph-Dvp.png?alt=media" alt=""><figcaption></figcaption></figure>

* *df*<sub>*p*</sub>​ and *df*<sub>*q*</sub>​ are the delayed frequency deviations used to compute the active and reactive power responses. They are obtained by applying the first-order transfer functions shown below to the frequency deviation signal.
  * *kp*<sub>*f*</sub>​ and *kq*<sub>*f*</sub> are the frequency-sensitivity coefficients for active and reactive power. These coefficients typically range from **−25 to +20**<sup>3</sup>, depending on the load type.
  * The frequency deviation is calculated as the difference between the load bus frequency and the nominal system frequency. In practice, the bus frequency is derived from the rate of change of the load bus voltage angle.
  * *tpf* and *tqf* are the frequency-dependence time constants for the active and reactive power responses.
  * *t*<sub>*1​*</sub> is the dynamic load time constant.

<figure><img src="https://3623212549-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FLxgTpoh7kyPmQ5vuyqD7%2Fuploads%2Fgit-blob-b11e174d24da709fb2237741f8f4ab5fa3df5692%2Feph-dfp.png?alt=media" alt=""><figcaption></figcaption></figure>

<table data-search="false"><thead><tr><th>Symbol</th><th>Description</th></tr></thead><tbody><tr><td><strong>ID</strong></td><td>Load name (Load ID)</td></tr><tr><td><strong>Status</strong></td><td>Initial Status, Connected (1) Disconnected (0)</td></tr><tr><td><strong>Bus</strong></td><td>Bus name (Bus ID)</td></tr><tr><td><strong>P</strong></td><td>Active power (MW)</td></tr><tr><td><strong>Q</strong></td><td>Reactive power (MVAr)</td></tr><tr><td><strong>kp1</strong></td><td>First voltage dependence coefficient for P (%)</td></tr><tr><td><strong>kp2</strong></td><td>Second voltage dependence coefficient for P (%)</td></tr><tr><td><strong>kp3</strong></td><td>Third voltage dependence coefficient for P (%)</td></tr><tr><td><strong>ep1</strong></td><td>First voltage dependence exponent for P</td></tr><tr><td><strong>ep2</strong></td><td>Second voltage dependence exponent for P</td></tr><tr><td><strong>ep3</strong></td><td>Third voltage dependence exponent for P</td></tr><tr><td><strong>kq1</strong></td><td>First voltage dependence coefficient for Q (%)</td></tr><tr><td><strong>kq2</strong></td><td>Second voltage dependence coefficient for Q (%)</td></tr><tr><td><strong>kq3</strong></td><td>Third voltage dependence coefficient for Q (%)</td></tr><tr><td><strong>eq1</strong></td><td>First voltage dependence exponent for Q</td></tr><tr><td><strong>eq2</strong></td><td>Second voltage dependence exponent for Q</td></tr><tr><td><strong>eq3</strong></td><td>Third voltage dependence exponent for Q</td></tr><tr><td><strong>KPfreq</strong></td><td>Frequency sensitivity coefficient for P</td></tr><tr><td><strong>KQfreq</strong></td><td>Frequency sensitivity coefficient for Q</td></tr><tr><td><strong>v0</strong></td><td>Nominal operating voltage (pu)</td></tr><tr><td><strong>range</strong></td><td>The width of normal range (pu)</td></tr><tr><td><strong>t1</strong></td><td>Load delay (s)</td></tr><tr><td><strong>tpv</strong></td><td>Voltage dependence time constant for active power (s)</td></tr><tr><td><strong>tqv</strong></td><td>Voltage dependence time constant for reactive power (s)</td></tr><tr><td><strong>tpf</strong></td><td>Frequency dependence time constant for active power (s)</td></tr><tr><td><strong>tqf</strong></td><td>Frequency dependence time constant for reactive power (s)</td></tr></tbody></table>

References

1. IEEE Standared Association. "IEEE guide for load modeling and simulations for power systems." Proccedings of the IEEE Std (2022): 2781-2022.
2. Milanović, Jovica V., et al. Modelling and aggregation of loads in flexible power networks. CIGRE-INT. COUNCIL ON LARGE ELECTRIC SYSTEMS, 2014.
3. Milanović, Jovica V., et al. Modelling and aggregation of loads in flexible power networks. CIGRE-INT. COUNCIL ON LARGE ELECTRIC SYSTEMS, 2014.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/hypersim/model-and-simulation/phasor-domain-with-ephasorsim/integrate-a-power-system-model-to-ephasorsim/native-library-components/load-components/dynamic-load-model.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
