> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/ni-slsc-modules/analog-bidirectional-modules/op8930-description.md).

# OP8930 Description

16 analog I/O conditioning module

<figure><img src="https://2438675663-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FrYR5dUDCbEE35IWamogp%2Fuploads%2FAE18Xw6JCEnb3Uy0Ra5t%2Fimage.png?alt=media&amp;token=648f1bfd-d867-47fd-bd81-0717140e595d" alt=""><figcaption></figcaption></figure>

The **OP8930** SLSC module is a 16 configurable differential analog input and output conditioning module with high bandwidth and fault insertion capabilities.

## Key features <a href="#key-features" id="key-features"></a>

* Analog signal conditioning & FIU on a single board
* 16 channels on two 8-channel OP8Gxx modules
* Analog in and Analog out user-configurable conditioning circuit
* Fault insertions unit FIU as an option

## Module architecture <a href="#board-architecture" id="board-architecture"></a>

The module features 2 groups of 8 channels and a set of relays adding fault insertion capability for each signal.

The general layout of the board is as follows, with the **front interface connectors** on the **left** and the **SLSC backplane connectors** on the **right**.

<figure><img src="https://2438675663-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FrYR5dUDCbEE35IWamogp%2Fuploads%2FqZs6nCRMT7mGMap3TJCB%2Fimage.png?alt=media&amp;token=aa9daeba-8aea-4d5d-8771-570a60ffc102" alt=""><figcaption></figcaption></figure>

\
The input/output conditioning is managed by the OPAL-RT OP89G10 and OP89G30 I/O modules.

The [FIU specification and topology](https://www.opal-rt.com/docs/ni-slsc-modules/op8900-slsc-modules-overview/modules-and-fiu-description.md#fault-insertion-unit-fiu-description) are common to all OP8900 boards.

## Analog input channel architecture <a href="#input-channel-architecture" id="input-channel-architecture"></a>

The OP8G01 module (P/N 126-0612) conditions **±10V** or **±30V** **differential analog input** **signals** coming from the unit under test into **±10V single-ended analog signals** to be connected to the PXI chassis.

The range is configured in the software since revision PCB 2.0 (May 2020).

### Conditioning circuit configuration <a href="#conditioning-circuit-configuration" id="conditioning-circuit-configuration"></a>

The **conditioning circuit** is **user-configurable** by using **passive components on through-hole sockets**. Each channel is configurable independently. This feature allows adapting the module for:&#x20;

* Custom impedance matching
* Custom analog filter
* Custom analog divider

The configurable elements consist of a set of **three resistors** (**R\_A**, **R\_B**, **R\_C**) and **two capacitors** (**C\_A**, **C\_B**) as shown below.

<figure><img src="https://2438675663-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FrYR5dUDCbEE35IWamogp%2Fuploads%2FpDKM3wNnqj5IyAt3vsBM%2Fimage.png?alt=media&amp;token=ca089358-9236-411b-8392-d8ed9519cc15" alt=""><figcaption></figcaption></figure>

By default, **R\_C**, **C\_A** and **C\_B** are not installed, and **R\_A** and **R\_B** are **0 Ohm**.

Use the table below to locate these elements on the module:

<table data-search="false"><thead><tr><th>Channel</th><th>R_A</th><th>R_B</th><th>R_C</th><th>C_A</th><th>C_B</th></tr></thead><tbody><tr><td><strong>1</strong></td><td>R9</td><td>R3</td><td>R75</td><td>C5</td><td>C1</td></tr><tr><td><strong>2</strong></td><td>R23</td><td>R21</td><td>R108</td><td>C18</td><td>C12</td></tr><tr><td><strong>3</strong></td><td>R12</td><td>R4</td><td>R67</td><td>C7</td><td>C2</td></tr><tr><td><strong>4</strong></td><td>R26</td><td>R24</td><td>R107</td><td>C19</td><td>C13</td></tr><tr><td><strong>5</strong></td><td>R37</td><td>R35</td><td>R144</td><td>C27</td><td>C20</td></tr><tr><td><strong>6</strong></td><td>R53</td><td>R51</td><td>R173</td><td>C34</td><td>C30</td></tr><tr><td><strong>7</strong></td><td>R43</td><td>R36</td><td>R137</td><td>C28</td><td>C21</td></tr><tr><td><strong>8</strong></td><td>R55</td><td>R52</td><td>R170</td><td>C35</td><td>C33</td></tr></tbody></table>

## Analog output channel architecture <a href="#output-channel-architecture" id="output-channel-architecture"></a>

The OP8G03 module (P/N 126-0642) conditions ±10 V single-ended analog signals coming from the PXI chassis into **±20V** **differential analog output signals** (OP8934/OP8935) or **±10V differential analog output signals** (OP8931/OP8933) to be connected to the unit under test.

The **maximum current per channel** is **±50 mA continuous**, for a **maximum of 250 mA per OP8930 board.**

### Conditioning circuit configuration <a href="#conditioning-circuit-configuration.1" id="conditioning-circuit-configuration.1"></a>

The **conditioning circuit** is **user-configurable** by using **passive components on through-hole sockets**. Each channel is configurable independently.\
This feature allows adapting the module for:&#x20;

* Custom impedance matching
* Custom analog filter
* Custom analog divider

The configurable elements consist of a set of **three resistors** (**R\_A**, **R\_B**, **R\_C**) and **two capacitors** (**C\_A**, **C\_B**) as shown below.

<figure><img src="https://2438675663-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FrYR5dUDCbEE35IWamogp%2Fuploads%2FvTY1QHHo6X7wZc0kHUMI%2Fimage.png?alt=media&amp;token=96b4b798-9c5a-465d-9313-b542b82db94a" alt=""><figcaption></figcaption></figure>

By default, **C\_A** and **C\_B** are not installed, and **R\_A**, **R\_B** and **R\_C** are **10 Ohms**.

Use the table below to locate these elements on the module.

<table data-search="false"><thead><tr><th></th><th>PCB rev 1.0 R_A</th><th>PCB rev 1.0 R_B</th><th>PCB rev 1.0 R_C</th><th>PCB rev 1.0 C_A</th><th>PCB rev 1.0 C_B</th><th>PCB rev 2.0 R_A</th><th>PCB rev 2.0 R_B</th></tr></thead><tbody><tr><td><strong>1</strong></td><td>R11</td><td>R5</td><td>R77</td><td>C7</td><td>C3</td><td>R17</td><td>R16</td></tr><tr><td><strong>2</strong></td><td>R12</td><td>R6</td><td>R76</td><td>C8</td><td>C4</td><td>R19</td><td>R18</td></tr><tr><td><strong>3</strong></td><td>R24</td><td>R19</td><td>R87</td><td>C21</td><td>C16</td><td>R21</td><td>R20</td></tr><tr><td><strong>4</strong></td><td>R25</td><td>R20</td><td>R86</td><td>C22</td><td>C17</td><td>R23</td><td>R22</td></tr><tr><td><strong>5</strong></td><td>R38</td><td>R32</td><td>R104</td><td>C33</td><td>C31</td><td>R25</td><td>R24</td></tr><tr><td><strong>6</strong></td><td>R39</td><td>R33</td><td>R103</td><td>C34</td><td>C32</td><td>R27</td><td>R26</td></tr><tr><td><strong>7</strong></td><td>R52</td><td>R46</td><td>R125</td><td>C50</td><td>C46</td><td>R29</td><td>R28</td></tr><tr><td><strong>8</strong></td><td>R53</td><td>R47</td><td>R124</td><td>C51</td><td>C47</td><td>R31</td><td>R30</td></tr></tbody></table>

For **PCB Rev 2.0**:

* C\_A is aligned with R\_A
* C\_B is aligned with R\_B
* R\_C is between C\_A and C\_B

## Channels calibration <a href="#channels-calibration" id="channels-calibration"></a>

For both analog inputs and analog outputs, there is no internal calibration on the SLSC module. Through NI VeriStand or manually in the model, it is possible to include *m* x + *b* coefficients to compensate the errors and variation of the components on the cards.

**OPAL-RT TECHNOLOGIES does not provide the compensation coefficients.** In the [OP8930 specification page](https://www.opal-rt.com/docs/ni-slsc-modules/analog-bidirectional-modules/op8930-description/specifications.md), the exact function transfer is provided with the maximum expected gain error. Based on the required level of precision, the nominal coefficients can be used. If better precision is required to correct all errors including cabling and setup, here is a quick calibration procedure.

### Analog inputs manual calibration <a href="#analog-inputs-manual-calibration" id="analog-inputs-manual-calibration"></a>

**Required equipment:**

* Voltage source
* Calibrated precision voltmeter
* Simulator
* SLSC Chassis with OP893x

**Procedure:**

1. Connect a voltage source to all analog inputs and the voltmeter in parallel
2. Measure the voltage of the source with the voltmeter
3. In the simulation, measure the voltage on every channel
4. Repeat steps 2 and 3 for a few different voltages spread on the usable range, with a recommended minimum of 3 voltage values
5. Calculate a linear regression between the source given by the voltmeter and the voltage measured in the model for every channel
6. Include the coefficients calculated in step 5 into the model or built-in NI VeriStand calibration function

### Analog outputs manual calibration <a href="#analog-outputs-manual-calibration" id="analog-outputs-manual-calibration"></a>

**Required equipment:**

* Calibrated precision voltmeter
* Simulator
* SLSC Chassis with OP893x

**Procedure:**

1. From a basic simulation, output a DC voltage on every channel
2. Measure the voltage at the output of the SLSC card for every channel
3. Repeat steps 1 and 2 for a few different voltages spread on the usable range, with a recommended minimum of 3 voltage values
4. Calculate a linear regression between the voltage of the simulation and the voltage measured in the voltmeter for every channel
5. Include the coefficients calculated in step 4 into the model or built-in NI VeriStand calibration function

## Available configurations <a href="#op8910-configurations" id="op8910-configurations"></a>

Several assemblies of the OP8930 are available, as listed below, with different counts of inputs and outputs, and with or without the FIU section populated.

<table data-search="false"><thead><tr><th>Part Number</th><th>Description</th><th width="110.199951171875">Input</th><th width="110">Output</th><th width="110">FIU</th></tr></thead><tbody><tr><td><strong>OP8931-F</strong><br>Legacy configuration replaced by <strong>OP8934-F</strong></td><td>16 Aout differential from single-ended input with FIU SLSC Conditioning Board</td><td> </td><td>Single-to diff</td><td>16 diff. FIU</td></tr><tr><td><strong>OP8931-N</strong><br>Legacy configuration replaced by <strong>OP8934-N</strong></td><td>16 Aout differential from single-ended input SLSC Conditioning Board</td><td> </td><td>Single-to diff</td><td>N/A</td></tr><tr><td><strong>OP8932-F</strong></td><td>16 Ain differential to single-ended with FIU SLSC Conditioning Board</td><td>Diff-to-Single</td><td> </td><td>16 diff. FIU</td></tr><tr><td><strong>OP8932-N</strong></td><td>16 Ain differential to single-ended SLSC Conditioning Board</td><td>Diff-to-Single</td><td> </td><td>N/A</td></tr><tr><td><strong>OP8933-F</strong><br>Legacy configuration replaced by <strong>OP8935-F</strong></td><td>8 Ain/8 Aout with FIU SLSC Conditioning Board</td><td>Diff-to-Single</td><td>Single-to diff</td><td>16 diff. FIU</td></tr><tr><td><strong>OP8933-N</strong><br>Legacy configuration replaced by <strong>OP8935-N</strong></td><td>8 Ain/8 Aout SLSC Conditioning Board</td><td>Diff-to-Single</td><td>Single-to diff</td><td>N/A</td></tr><tr><td><strong>OP8934-F</strong></td><td>16 Aout differential from single-ended input with FIU SLSC Conditioning Board</td><td> </td><td>Single-to diff</td><td>16 diff. FIU</td></tr><tr><td><strong>OP8934-N</strong></td><td>16 Aout differential from single-ended input SLSC Conditioning Board</td><td> </td><td>Single-to diff</td><td>N/A</td></tr><tr><td><strong>OP8935-F</strong></td><td>8 Ain/8 Aout with FIU SLSC Conditioning Board</td><td>Diff-to-Single</td><td>Single-to diff</td><td>16 diff. FIU</td></tr><tr><td><strong>OP8935-N</strong></td><td>8 Ain/8 Aout SLSC Conditioning Board</td><td>Diff-to-Single</td><td>Single-to diff</td><td>N/A</td></tr></tbody></table>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/ni-slsc-modules/analog-bidirectional-modules/op8930-description.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
