> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/lp-bus-bar-module.md).

# LP Bus Bar Module

## Description <a href="#description" id="description"></a>

The LP  bus bar module is a **low-power (LP) distribution system** featuring an **internal bus bar** that provides a common connection between [OP8110 amplifiers](https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/op8110-4q-power-amplifier.md) and **up to three external** [**DUT**](#user-content-fn-1)[^1]**s**.

## Configuration

* **Three front-panel connection points** (three phases and neutral) to connect separate external DUTs to the common internal bus bar (fused at **35 A** per line).
* **Six rear-panel connection points** (three phases and neutral) to connect from the OP8110 amplifiers to the internal common bus bar

## Specifications <a href="#specifications" id="specifications"></a>

* Maximum voltage: **600 V**<sub>AC</sub> **/ 450 V**<sub>DC</sub>
* Maximum continuous DUT terminal current: **30 A**<sub>**RMS**</sub> per line
* Maximum continuous amplifier terminal current: **14 A**<sub>RMS</sub> per line
* Control supply: **24 V**<sub>DC</sub>

## **Protection and safety** <a href="#protection-and-safety" id="protection-and-safety"></a>

* Fuse protection for each DUT output
* Contactor and logic interlock prevent unintended energization
* Compatible with E-Stop and enclosure interlock circuits
* All metal parts grounded for safety and continuity

## Front panel <a href="#front-and-rear-panels" id="front-and-rear-panels"></a>

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2Fb3gwNNUUWklrB2okFQqv%2Fimage.png?alt=media&amp;token=5125247b-8f39-4fc3-b0ae-23faf1cb449f" alt=""><figcaption></figcaption></figure>

* **24V ON** - Auxiliary power LED indicator
* **BUS ON -** LED indicator (ON when at least 60V<sub>RMS</sub> is detected on any line voltage (L-L))
* 3 external DUT control/interface sections (DUT 1, DUT 2, DUT 3)
  * **L1** (<mark style="color:$danger;">**red**</mark>), **L2** (**black**), **L3** (<mark style="color:blue;">**blue**</mark>), and **N** (white) banana jack terminals
  * Contactor control button
    * **Start** - Enables DUT connection
    * **Stop** - Disables DUT connection
  * Status Indicator LED
    * **Flashing** – Enable active, waiting for remote command
    * **Solid ON** – DUT connection enabled (contactor closed)
    * **OFF** – DUT connection disabled (contactor opened)

## Rear panel <a href="#front-and-rear-panels" id="front-and-rear-panels"></a>

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FYwDSu2eS0iDktWcuo7P2%2Fimage.png?alt=media&amp;token=9df0eb74-95aa-4473-8df3-5df8f8442a19" alt=""><figcaption></figcaption></figure>

* **GND -** Voltage Reference/Functional Ground banana jack
* **ETH/DIO** - Toggle switch. Selects the source of the internal contactor control, either Ethernet or digital I/O.
* **Protective Earth (PE)** grounding stud
* **ETH -** RJ45 plug for ethernet cable connection
* **P1 (24 VDC)** - Connector, 24 V supply - Supports daisy-chaining with other compatible modules
* **DI -** DB37 connector, digital inputs for controlling the contactors
* **DO -** DB37 connector, digital outputs forwarded from unused digital inputs
* **AO1 -** DB37 connector, analog output **voltage measurement** signals
* **AO2 -** DB37 connector, analog output **current measurement** signals
* **6 sets** of **banana jack terminals** for connection with [**OP8110 amplifiers**](https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/op8110-4q-power-amplifier.md)
  * They are identified as **AMP1**, **AMP2**, and **AMP3**
  * Each AMP is divided into **2 groups**, identified as **GR 1** and **GR 2**.
    * Each group has 3 wires and a neutral identified
      * For group 1 (**GR 1**): **L1** (<mark style="color:red;">**red**</mark>), **L2** (**black**), **L3** (<mark style="color:blue;">**blue**</mark>), and **N** (white)
      * For group 2 (**GR 2**): **L4** (<mark style="color:red;">**red**</mark>), **L5** (**black**), **L6** (<mark style="color:blue;">**blue**</mark>), and **N** (white)

{% hint style="danger" %}
The rear panel banana jack terminals should **only** be used for connecting **from the OP8110 amplifiers**.
{% endhint %}

## Contactor control <a href="#contactor-control" id="contactor-control"></a>

Each DUT output is switched by contactors, which can be remotely controlled via Ethernet or digital I/O signals, selectable using the associated toggle switch on the rear panel. In addition to the remote signal, the physical local Enable button must also be active for the contactor to close, providing an extra layer of safety.

{% hint style="danger" %}
**SAFETY WARNING!**

The **protective earth (PE)** connection of the **Device Under Test (DUT)** is the responsibility of the user.

Operation of a DUT with exposed conductive parts without a proper **protective earth (PE) connection** may result in an **electric shock hazard**.
{% endhint %}

## Electrical schematic <a href="#electrical-schematic" id="electrical-schematic"></a>

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FgGrigNVBRpQTwf6VTuKq%2Fimage.png?alt=media&amp;token=848011db-f0aa-442f-bd49-364088a5a23f" alt=""><figcaption></figcaption></figure>

## Digital I/O connectors <a href="#digital-io-connectors" id="digital-io-connectors"></a>

These female DB37 connectors are provided to interface with the digital outputs of an IO card inside a simulator.

### Digital input (DI) connector

The **digital inputs** on the **DI connector** allow you to switch ON (logical '1') or OFF (logical '0') the DUT contactors when the **DUT Enable button** is activated.

The following table and DB37 schematic list the pin assignments of this connector.

{% tabs %}
{% tab title="Pin assignment table" %}

| DB37F        | Pin assignment                 | DB37F        | Pin assignment                |
| ------------ | ------------------------------ | ------------ | ----------------------------- |
| **1**        | Validation bit                 | **20**       | Validation bit return         |
| **2**        | DUT 1 command                  | **21**       | DUT 1 return                  |
| **3**        | DUT 2 command                  | **22**       | DUT 2 return                  |
| **4**        | DUT 3 command                  | **23**       | DUT 3 return                  |
| **5 to 17**  | Forwarded to the DO connector  | **24 to 36** | Forwarded to the DO connector |
| **18**       | 24 V (supplied by the bus bar) | **37**       | GND                           |
| {% endtab %} |                                |              |                               |

{% tab title="DB37 schematic" %}

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FBGsBZreqjNXBdLk7xb5X%2Fimage.png?alt=media&amp;token=b37fd8aa-cc72-43d6-8fd3-e49193f119cc" alt="" width="159"><figcaption></figcaption></figure>
{% endtab %}
{% endtabs %}

### Digital output (DO) connector

The **digital outputs** on the **DO connector** can be used to access the unused digital outputs of the [OP5360](https://www.opal-rt.com/docs/op53xx/digital-output-modules/op5360-description.md) by daisy-chaining another piece of equipment to the LP bus bar.

Please contact your [OPAL-RT local representative](https://www.opal-rt.com/contact-us/#offices-and-distributors) if you require further information on this feature.

### Analog output (AO) connectors <a href="#analog-output-connectors" id="analog-output-connectors"></a>

Two female DB37 connectors provide the **voltage** (**AO1**) and **current** (**AO2**) **measurement signals**.

| Analog output 1 (AO1) connector (voltages)                                                                                                                                                                                                                | Analog output 2 (AO2) connector (currents)                                                                                                                                                                                                                |
| --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- | --------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------- |
| <img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2F9oKskkhiB5jC1JNhChHO%2Fimage.png?alt=media&amp;token=3e56ace1-2e5b-45b2-be93-8ad04960a754" alt="" data-size="original"> | <img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FSF7BBxADcetUhDAux7Q0%2Fimage.png?alt=media&amp;token=04285780-1028-4b6b-b201-aa5cb5df5647" alt="" data-size="original"> |

[^1]: Device Under Test


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/lp-bus-bar-module.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
