> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/op8110-4q-power-amplifier.md).

# OP8110 4Q Power Amplifier

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2F8oV8zL3kkBjV4KLgROvk%2Fimage.png?alt=media&amp;token=01f1d7e4-730b-4552-b031-433ade609dca" alt=""><figcaption></figcaption></figure>

## Description <a href="#description" id="description"></a>

The **OP8110 4-Quadrant Power Amplifier** is the heart of the OPAL-RT line of OP1400PR PHIL Prime Series test benches. It is an **ultra-compact (2U) 4-quadrant**, **3 or 6 outputs**, **Power Soft-Switching Amplifier**.

The OP8110 can **operate in both DC and AC modes** with a bandwidth of **10 kHz** with a low noise floor, high slew rate, and low harmonic distortion.

The OP8110 power amplifier **can be directly controlled by OPAL-RT simulation platforms** through a **high-speed fiber-optic SFP link**, enabling it to **emulate different operating configurations** such as

* 3 phases, 0 to 208 V<sub>L-L,RMS</sub>
* 0 to 400 V<sub>DC</sub> bus

Multiple OP8110 amplifiers can be **controlled in tandem by OPAL-RT’s simulation platforms** to obtain other configurations. Some **examples** include:

* 3 phases, 0 to 415 V<sub>L-L RMS</sub>
* Single phase, 0 to 120 V<sub>L-L RMS</sub> or 0 to 240 V<sub>L-L,RMS</sub>

The power level and number of simultaneous outputs differ between the different OP1400PR test bench models, providing ample flexibility in selecting a suitable hardware platform for a wide range of applications needs.

The OP8110 is suitable for installation in any typical laboratory environment, featuring forced ambient air cooling with variable-speed fans along with both hardware and firmware-based protections to safeguard it from improper input/output connections (including short-circuit/overcurrent conditions and over/under voltages) as well as over-temperature conditions.

The OP8110 amplifier comes in **two variations** depending on **the number of outputs included**:

* OP8110-3 (3 outputs)
* OP8110-6 (6 outputs)

### OP8110-3

**Three amplifier outputs (L1, L2, L3)** and their associated **neutrals (N1, N2, N3)** from **one output group:** **Group 1**.

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FqMoQeUyMtSgr57L4fjhT%2Fimage.png?alt=media&amp;token=c7b8a2fb-fed5-4f76-958d-5d9d0a959ba2" alt=""><figcaption><p>OP8110-3</p></figcaption></figure>

### OP8110-6

**Six amplifier outputs (L1, L2, L3, L4, L5, L6)** and their associated **neutrals (N1, N2, N3, N4, N5, N6)** from **two output groups** (**Group 1** and **Group 2**).

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FD3CqMyyPmPV34gaTuy9A%2Fimage.png?alt=media&amp;token=33d986e6-0720-4a9f-9b78-8b77292b47b7" alt=""><figcaption><p>OP8110-6</p></figcaption></figure>

## Electrical schematic <a href="#electrical-schematic" id="electrical-schematic"></a>

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FvQ6vIZz24xIMbUD8PUQv%2Fimage.png?alt=media&amp;token=0a4ef992-5c48-40f1-9cc4-1d2b46993304" alt=""><figcaption></figcaption></figure>

## Power stage topology overview <a href="#particularities" id="particularities"></a>

### Particularities <a href="#particularities" id="particularities"></a>

#### Neutral point <a href="#neutral-point" id="neutral-point"></a>

A neutral point is made available for every output of the OP8110. The neutral point is a regulated DC mid point node. Since it is coupled through capacitors, DC current cannot circulate through the neutral point. Refer to the [OP8110 specifications page](https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/op8110-4q-power-amplifier/specifications.md) for more details and limitations at low frequency.

#### Output link inductance <a href="#output-link-inductance" id="output-link-inductance"></a>

The OP8110 features a **bypassable 75 µH output inductor** on **every output**, which allows coupling **directly to capacitive loads**, such as input DC nodes on inverters or other OP8110 amplifier outputs.

#### DC precharge <a href="#dc-precharge" id="dc-precharge"></a>

The OP8110 features an **embedded DC precharge** **circuit** to limit the inrush current when powering on the 500 V DC supply.

The DC precharge **does not protect the EMI filtering capacitors**.

As such, **the OP8110 should always only be used with the DC power supplies provided inside the OP1400PR Series test bench**. If another DC power supply is used nevertheless, the voltage slew rate should be limited to **5 V/ms or less** when turning on the DC voltage. <mark style="color:$danger;">**Failure to do so may damage the OP8110**</mark>.

**Software protections** are implemented to **avoid overheating the precharge resistors**. As such, immediate consecutive precharges will not be allowed by the OP8110. In the case the precharge is blocked by the OP8110 software, unpower the DC supply and wait for approximately 5 minutes before re-enabling the precharge.

### Use cases <a href="#application-exemples" id="application-exemples"></a>

#### 120/208 V<sub>RMS</sub> 3φ applications <a href="#id-120-208-vrms-3f-applications" id="id-120-208-vrms-3f-applications"></a>

* Requires 1 x OP8110 3-output group
* Requires 1 x DC power supply
* AC balanced/unbalanced output configuration

<table><thead><tr><th valign="top">DC bus configuration
single DC source</th><th valign="top">Balanced/Unbalanced three-phase + neutral</th><th valign="top">Balanced three-phase</th></tr></thead><tbody><tr><td valign="top"><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FYNCIfm49PzCHMsCB8dLz%2Fimage.png?alt=media&amp;token=a39441a3-ecc5-485f-8e01-e10200d75df0" alt="" data-size="original"></td><td valign="top"><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FTbxREHjHhGelkNGXaBTL%2Fimage.png?alt=media&amp;token=d80d2cae-ed61-4982-af0e-2af8d69bf574" alt="" data-size="original"></td><td valign="top"><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FxGgSVY0o9Wl8bnP1Jli4%2Fimage.png?alt=media&amp;token=6811ee8e-4e3a-40b3-b0fd-c82a95edc4bc" alt="" data-size="original"></td></tr></tbody></table>

#### 230/400 V<sub>RMS</sub> 3φ applications <a href="#id-230-400-vrms-3f-applications" id="id-230-400-vrms-3f-applications"></a>

* Requires 3x OP8110 3-output groups
* Requires 3x isolated DC power supplies
* AC balanced/unbalanced output configuration
* Neutral must be grounded to meet isolation ratings of the OP8110

Two amplifier outputs of the three available per OP8110-3 are used to generate a 240 V<sub>RMS</sub> between their outputs.

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FVuMEa58eyU1TSKpKPu0x%2Fimage.png?alt=media&amp;token=dbe33055-9c78-47ba-9633-92da300b9910" alt=""><figcaption></figcaption></figure>

#### 400 V<sub>DC</sub> or single-phase 240 V<sub>RMS</sub> applications <a href="#id-400-vdc-or-single-phase-240-vrms-applications" id="id-400-vdc-or-single-phase-240-vrms-applications"></a>

* Requires 1 x OP8110 3-output group
* Requires 1 x DC Power Supply
* Neutrals not connected

<figure><img src="https://3155739458-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FzVJdfp93TWLISP6nkqTs%2Fuploads%2FWExwkms8F5khb6Y9OBG6%2Fimage.png?alt=media&amp;token=05b05b21-3e31-4d45-9ad6-d475b8ba555b" alt=""><figcaption></figcaption></figure>


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/op1400pr/op1400pr-overview/description-and-components/op8110-4q-power-amplifier.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
