> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/op5025xg/get-started/set-up-the-simulators-ip-address.md).

# Set Up the Simulator's IP Address

## Introduction <a href="#id-2.-connecting-the-cables" id="id-2.-connecting-the-cables"></a>

OPAL-RT pre-installs the operating system and assigns a default IP address, which is indicated on a sticker at the front of the simulator.

To integrate the simulator into your network, you will likely need to reconfigure this IP address.\
This procedure provides step-by-step instructions to update the IP address based on your network settings.

{% hint style="info" %}
If you connect the workstation directly to the simulator using a point-to-point Ethernet cable (no network infrastructure), you can keep the default IP address. In this case, refer to the **Get Started section** of your simulation platform.
{% endhint %}

{% stepper %}
{% step %}

## Power ON the simulator <a href="#id-1.-power-on-the-system.1" id="id-1.-power-on-the-system.1"></a>

1. Turn on the main power switch at the back of the simulator.
2. Press the power button on the front panel.
   {% endstep %}

{% step %}

## Log in to OPAL-RTLinux

Enter the following credentials at the OPAL-RTLinux login prompt:

**Username**: `root`

**Password**: Refer to the **System Description Document** provided with your hardware. If you cannot find the login credentials, contact [OPAL-RT Technical Support](https://www.opal-rt.com/contact-technical-support/).

After a successful login, the OPAL-RTLinux prompt appears as shown below:

<figure><img src="broken://spaces/7LhLoEldIvunS3fxYxrx/files/nDd8ZRkRBl0YfSSZf4sW" alt=""><figcaption></figcaption></figure>
{% endstep %}

{% step %}

## Check the current IP address

To verify the current IP address, type the following command:

`ip a`

The output should display network interfaces and their IP addresses. Note that `eno1` corresponds to the LAN1 Ethernet port  and `eno2` to the LAN2 Ethernet port.

<figure><img src="broken://spaces/7LhLoEldIvunS3fxYxrx/files/z29wGLb0rj9SfgVGktvL" alt=""><figcaption></figcaption></figure>

If command execution fails, contact [OPAL-RT Technical Support](https://www.opal-rt.com/contact-technical-support/).
{% endstep %}

{% step %}

## Configure a static IP address <a href="#id-4.-configure-a-static-ip-address.1" id="id-4.-configure-a-static-ip-address.1"></a>

1. Run the network configurator:

`opal_network_configurator`

2. Read and follow the prompts. Type `yes` and press **Enter** to proceed.

<figure><img src="broken://spaces/7LhLoEldIvunS3fxYxrx/files/2F00w0k5X4MB7c641dSV" alt=""><figcaption></figcaption></figure>

3. Read or skip the IPMI Information section and the Oregano Card section. Then read and follow the prompts of the **Setting Up Network Interfaces** section. The script will list the network interfaces one by one, starting with `eno1`.
   1. **To configure a new static IP address** for `eno1`, type the desired IP address including the netmask: `xxx.xxx.xxx.xxx/xx` and press **Enter**. For example, to set the IP `10.64.110.204` with a `/19` netmask (optional, default: 255.255.224.0), type `10.64.110.204/19` and press **Enter**.
   2. To configure `eno1` for DHCP, type `dhcp` and press **Enter**. OPAL-RT software requires the simulator's IP address to run models. Therefore, **DHCP mode is not recommended**.
   3. To keep the IP address of `eno1` unchanged and proceed to the next network interface, simply press **Enter** without typing anything.

      <figure><img src="broken://spaces/7LhLoEldIvunS3fxYxrx/files/Ivie0B8kLT8ShSFNJqhQ" alt=""><figcaption></figcaption></figure>
   4. Press **Enter** to skip the configuration of subsequent network interfaces until the network restarts.

      <figure><img src="broken://spaces/7LhLoEldIvunS3fxYxrx/files/NZ2Kf5sL6G0WAaB0kCY5" alt=""><figcaption></figcaption></figure>

Additional network interfaces can also be configured if desired. Follow the on-screen prompts as you did for `eno1`.
{% endstep %}

{% step %}

## Verify the new IP address <a href="#id-5.-verify-the-new-ip-address.1" id="id-5.-verify-the-new-ip-address.1"></a>

To verify the new IP address, type `ip a` and validate the IP address.
{% endstep %}
{% endstepper %}


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/op5025xg/get-started/set-up-the-simulators-ip-address.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
