> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/rt-lab/simulink-blocks-reference/artemis-library/ssn-tsb-rd-2-level-3-level-npc-3-level-t-type.md).

# SSN TSB-RD (2-level, 3-level NPC, 3-level T-type)

## Description

<figure><img src="https://96827845-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FNRdpSk8kjn20gXAexnt6%2Fuploads%2Fgit-blob-bbcc1b2f3f57d17df314fe2a5b6501286da88666%2FArtemis_TSB_RD_block.png?alt=media" alt="" width="563"><figcaption></figcaption></figure>

The **TSB-RD** blocks, located in the **ARTEMiS/SSN/TSB-RD** library, implement a new generation of Time-Stamped Bridge (TSB) with real diodes. They support the interpolation methods of the previous TSB generation. High-impedance and rectifying modes are implemented with real SPS diodes or with a combination of SPS switches and thyristors (enablable diodes). Compared to the previous generation that used a zero-current feedback loop for high-impedance mode, TSB-RD blocks are generally more stable and work with RC snubbers of higher impedance.

The TSB-RD family includes the following 3-phase inverters:

* 2-level,
* 3-level neutral-point-clamped (NPC),
* and 3-level T-type.

and 3-level NPC 2-phase inverters.

TSB-RD blocks support dead-time smaller than the simulation time step, and the 2-level variant supports parallel operation with firing delays between stages.

The TSB-RD are built using real SPS switches, diode and/or thyristor. All 3-phase inverters (2-level, 3-level NPC and 3-level T-type) have 9 internal SPS switches, which is close to the typical limit for pre-calculation methods in real-time systems. The TSB-RD inverters are therefore best used in conjunction with SSN and put each inverter in a unique SSN group.

{% hint style="danger" %}
This block requires a valid RT-LAB license on the simulator with the feature ARTEMiS enabled. Refer to[ ARTEMiS Requirements](https://www.opal-rt.com/docs/rt-lab/model-and-simulation/power-systems-with-artemis/artemis-requirements.md) for details.
{% endhint %}

## Mask parameters

<figure><img src="https://96827845-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FNRdpSk8kjn20gXAexnt6%2Fuploads%2Fgit-blob-4d6d33882b2c6d0a59b2cb144063bfff1da85c50%2FArtemis_TSB_RD_mask.png?alt=media" alt=""><figcaption></figcaption></figure>

{% tabs %}
{% tab title="3-level NPC, 2 ph" %}

| Parameter                               | Description                                        |
| --------------------------------------- | -------------------------------------------------- |
| **Switch conduction resistance (Ohms)** | The IGBT/GTO/MOSFET conduction resistance in Ohms. |
| **Active Switch Forward Voltage**       | The IGBT/GTO/MOSFET forward voltage in volts.      |
| **Diode Forward Voltage**               | The anti-parallel diode forward voltage in volts.  |
| **Snubber resistance (ohms)**           | The snubber resistance in ohms.                    |
| **Snubber Capacitance (F)**             | The snubber capacitance in Farads.                 |
| {% endtab %}                            |                                                    |

{% tab title="2-level 3 ph" %}

| Parameter                               | Description                                                                                                                                                            |
| --------------------------------------- | ---------------------------------------------------------------------------------------------------------------------------------------------------------------------- |
| **Switch conduction resistance (Ohms)** | The IGBT/GTO/MOSFET conduction resistance in Ohms.                                                                                                                     |
| **Snubber resistance (ohms)**           | The snubber resistance in ohms.                                                                                                                                        |
| **Snubber Capacitance (F)**             | The snubber capacitance in Farads.                                                                                                                                     |
| **Sample Time (s)**                     | Time at which the capacitor voltage will be computed.                                                                                                                  |
| **Parallel TSB option**                 | Enables the TSB-RD to operate in parallel. In this case, the blocks' 'Itotal' input of all parallel TSB-RD must be fed with the sum of the 'Iabc' from all the TSB-RD. |
| {% endtab %}                            |                                                                                                                                                                        |

{% tab title="3-level NPC 3 ph" %}

| Parameter                         | Description                                        |
| --------------------------------- | -------------------------------------------------- |
| **Switch Ron (Ohms)**             | The IGBT/GTO/MOSFET conduction resistance in Ohms. |
| **Active Switch Forward Voltage** | The IGBT/GTO/MOSFET forward voltage in volts.      |
| **Diode Forward Voltage**         | The anti-parallel diode forward voltage in volts.  |
| **Snubber Capacitance (F)**       | The snubber capacitance in Farads.                 |
| {% endtab %}                      |                                                    |

{% tab title="T-type 3 ph" %}

| Parameter                     | Description                                        |
| ----------------------------- | -------------------------------------------------- |
| **Switch Ron (Ohms)**         | The IGBT/GTO/MOSFET conduction resistance in Ohms. |
| **Snubber resistance (ohms)** | The snubber resistance in ohms.                    |
| **Snubber Capacitance (F)**   | The snubber capacitance in Farads.                 |
| {% endtab %}                  |                                                    |
| {% endtabs %}                 |                                                    |

{% hint style="info" %}
*The snubbers are always ‘in circuit’ as they are modeled by SPS components, unlike the previous generation of TSB where snubber was in-circuit only during high-impedance mode.*
{% endhint %}

## Conserving ports

| Port           | Description                                                                               |
| -------------- | ----------------------------------------------------------------------------------------- |
| **V+, Vn, V-** | DC-bus connection points. (Vn is the neutral connection point for 3-level inverters only) |
| **A, B, C**    | Inverter outputs for phases A, B, and C.                                                  |

## Inputs

| Input                     | Description                                                                                                |
| ------------------------- | ---------------------------------------------------------------------------------------------------------- |
| **g**                     | IGBT/GTO/MOSFET gate input signals.                                                                        |
| **Itotal (only 2-level)** | Total inverter output current from all parallel inverters. Used only when 'Parallel TSB option' is enabled |

## Outputs

| Output                  | Description                        |
| ----------------------- | ---------------------------------- |
| **Iabc (only 2-level)** | Inverter output currents in Ampere |


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/rt-lab/simulink-blocks-reference/artemis-library/ssn-tsb-rd-2-level-3-level-npc-3-level-t-type.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
