> For the complete documentation index, see [llms.txt](https://www.opal-rt.com/docs/llms.txt). Markdown versions of documentation pages are available by appending `.md` to page URLs; this page is available as [Markdown](https://www.opal-rt.com/docs/smart-power-simulation-software-sps/example-models/power-converters/series-load-resonant-converter.md).

# Series Load Resonant Converter

This example shows the operation of a series load resonant converter.

<figure><img src="https://799605156-files.gitbook.io/~/files/v0/b/gitbook-x-prod.appspot.com/o/spaces%2FdlNg8IbOdahCpFCyzxSN%2Fuploads%2Fgit-blob-432266f478ea35fe99aec160bb5c3d1ac8c986f9%2Fseries_laod_resonant_conveter_example.png?alt=media" alt=""><figcaption></figcaption></figure>

## Description

The Series Load Resonant (SLR) converter is a DC/DC converter based on a resonant circuit which allows soft-switching operation. In a soft-switching converter, switching occurs when voltage and/or current values are zero, significantly improving converter efficiency. A switch is said to have zero-voltage switching (ZVS) / zero-current switching (ZCS) when the voltage/current is zero as the switch changes state.

The converter consists of a full-bridge MOSFET bridge, a resonant tank represented by Lr and Cr, a full-bridge rectifier and an output filter (Co). The resonant frequency of the tank is given by:

$$
\omega\_r=1/\sqrt{L\_r \times C\_r} = 2 \times \pi \times f\_r
$$

The switching frequency f<sub>s</sub> range determines the three possible operating modes of the SLR converter:

* Discontinuous Conduction Mode (DCM), where f<sub>s</sub> < f<sub>r</sub>/2, leading to ZVS and ZCS at turn-off and a ZCS at turn-on.
* Continuous Conduction Mode (CCM1), where f<sub>r</sub>/2 < f<sub>s</sub> < f<sub>r</sub>, leading to ZVS and ZCS at turn-off.
* Continuous Conduction Mode (CCM2), where f<sub>s</sub> > f<sub>r</sub>, leading to ZVS at turn-on.

## Simulation

In this example the resonant frequency f\_r = 11.25 kHz. Select a switching frequency f\_s = 13.14 kHz (conduction mode 3 = CCM2) and run the simulation. Observe waveforms on Scope 1 and Scope 2.

{% stepper %}
{% step %}

### Run the base simulation

* Set switching frequency f\_s = 13.14 kHz (CCM2).
* Run the simulation.
* Observe waveforms on Scope 1 and Scope 2.
  {% endstep %}

{% step %}

### Vary load and conduction mode

* For a 0.5 Ω load and 12 V input, you should get a \~10 V output.
* Try other conduction modes and/or change the load from 0.5 Ω to 5 Ω.
* Observe how the output deviates from 10 V due to the DC gain characteristic of the resonant circuit for a given load.
* Observe the DC gain characteristic plot (0.5 Ω traces): experimental gain values are slightly shifted relative to theoretical values. This is because the output filter Co is not included in the theoretical gain calculation.
* Also, at light load (e.g., 5 Ω), the SLR converter is harder to regulate — the DC gain characteristic shows stronger deviation.
  {% endstep %}
  {% endstepper %}

## Command

Example model name: power\_SLRConverter

{% code lineNumbers="true" %}

```matlab
open('power_SLRConverter')
```

{% endcode %}

## Reference

T. Taufik, M. McCarthy, S. Watkins, M. Anwari; "Performance Study of Series Loaded Resonant Converter Using Super Barrier Rectifiers", IEEE, TENCON 2009.


---

# Agent Instructions
This documentation is published with GitBook. GitBook is the documentation platform designed so that both humans and AI agents can read, navigate, and reason over technical content effectively. Learn more at gitbook.com.

## Querying This Documentation
If you need additional information that is not directly available in this page, you can query the documentation by asking a question.

Perform an HTTP GET request on the following URL with the `ask` and `goal` query parameters:

```
GET https://www.opal-rt.com/docs/smart-power-simulation-software-sps/example-models/power-converters/series-load-resonant-converter.md?ask=<question>&goal=<user_goal>
```

`ask` is the immediate question: it should be specific, self-contained, and written in natural language.
`goal` is what the user is ultimately trying to achieve, the reason they need the answer. Sharing it helps GitBook give you a better, more relevant answer. A goal is most helpful when it describes the outcome the user wants rather than restating the question. For example, with `ask=how do I create an API token`, a goal like `automate deployments from our CI pipeline` lets GitBook tailor the answer to that use case.

The response will contain a direct answer to the question and relevant excerpts and sources from the documentation.

Use this mechanism when the answer is not explicitly present in the current page, you need clarification or additional context, or you want to retrieve related documentation sections.
